Video Results for "plastic injection molding"
Portland, OR - "plastic injection molding" search results
About Plastic Injection Molding
Local Plastic Injection Molding is a wonderful manufacturing process that produces parts from thermosetting plastic materials. The materials are fed into heated barrels, mixed, and are also forced into mold cavities where it then cools and hardens to the configurations of the mold cavities. Your products are usually designed, by industrial designers or engineers. Local Plastic Injection Molding is largely used for plastic housings. There are many other things that its used for like powers tools, buckets, small plastic toys, and household appliances. However, there are many steps that are used. First step happens to be clamping. Each halves of the mold are secured, attached to the injection molding machine and then one half of your mold is able to slide. After wards, the hydraulically powered clamping unit pushes the mold halves together then places at the right enough of force thats needed so that the injection can be inserted in to the material. It depends on how long your machine should be clamped. The larger machines would take the longest, because of the greater clamping forces. To help it along, time could also be estimated from a dry cycle time that the machine has. Second process for the Local Plastic Injection Molding is injection. The raw plastic material is fed into an injection molding machine that advances toward the mold by an injection unit. Then goes through a process that the material gets melted by heat and pressure. In a very fast fashion, the molten plastic is injected in a mold, referred to as a shot. The time that it takes to inject is real hard to determine. But, it can be tried using the shot volume, and power.
Rubber & Plastic Inc
7401 NE 47th Ave, Vancouver, WA 98661(360) 567-4280 Write a review
Advanced Plastic Produts Inc
4601 NE 78th St, Vancouver, WA 98665(360) 546-2300 Write a review
Roseway Remolding LLC
7902 NE St Johns Rd, Vancouver, WA 98665(360) 574-5065 Write a review
Jones Plastics Technology
4307 NE 139th St, Vancouver, WA 98686(360) 892-5390 Write a review
Salmon Creek Plastic Surgery
13716 NE 10th Ave, Vancouver, WA 98685(360) 823-0860 Write a review
R & R Plastics
3109 NE 65th St Ste F, Vancouver, WA 98663(360) 696-2186 Write a review
Western Industrial Plastics Inc
1899 SE Spinaker Way, Vancouver, WA 98661(360) 571-8549 Write a review
3002 N Wygant St, Portland, OR 97217(503) 285-0318 Write a review
Diesel Fuel Injection Service
8922 NE Vancouver Way , Portland, OR 97211(503) 235-1947
Call TodayWrite a review
DC2 Construction Inc.
3412 NE 127th St , Vancouver, WA 98686(503) 887-4516
Call TodayWrite a review
10107 NW 3rd Ct, Vancouver, WA 98685(360) 907-1312 Write a review
More on Plastic Injection Molding
Third thing that is to be done is the cooling process. During this Local Plastic Molding process the molten plastic that happens to be inside the mold starts to cool off. As it is makes contact with the inside mold surface, it will then become a solid thatll form a shape that is needed for the part. As it is cooling there will be some shrinking of the molten plastic. But dont worry because the packaging of the material used allows for the material to flow into the mold that will then reduce so the shrinking isnt so visible. The timing on this process is not so hard to determine, you have the thermodynamic properties of the plastic that will help you out. Last but not least, the Local Plastic Injection Molding process has to go through an ejection process. The cooled part is then ejected from the mold by an ejection system, after enough time has been allotted for it to cool. Then you use a device to push the plastic out of the mold. To eject the plastic, a lot of strength has to be used because during the time the cooling was done, the mold has shrunk. To help out with the Local Plastic Injection Molding process you can estimate the time it takes to open the mold and eject it by the dry cycle time of the machine. Making sure you keep in mind of the type of the mold you are dealing with. Then the clamp is closed so you can then inject your next mold.